rigger
06-29-2010, 06:08 PM
I really hate to do this but I need the money more than the machine so I am putting my R up for sale. I would rather sell her as a complete machine but if it does not sell in the next month or two, I will start to part her out.
First of all, I am located in Charleston SC. If you were to want it shipped, as long as I get good funds and you cover all shipping charges, I will build a crate and ship it from my work.
Fully gusseted 1986 frame, also modified to run the 89’ swing arm/suspension set up on the rear. 89 swing arm and 89 linkage. Works front triple rate shocks and Works rear built and valved for recreational ride for someone around 160-200 pounds. RPM adjustable width axle. Lone Star Racing plus 2, plus 1 front end. (she sits at about 50” wide). All new ball joints, heim joints and cone spacers. New 6ply tires, 400EX front brake set up with SS lines. Full chassis skid plates, FMF pipe, 36mm Duncan Racing Carb w/twist throttle. New bars and grips. New air filter and brake pads. New chain and sprockets. Good seat and plastics with a big gas tank. All new gaskets and seals. Ported motor. Milled head for higher compression (195psi) need to run race gas in her. She uses the newer style long rod crank and piston from the 88-89 motors. Crank is fairly new and I just put new crank bearings in it while I had the motor apart.
I might have 2 hours of ride time on her, if that.
I built her from just a frame over about a year and half and she has pretty much not been ridden over the last year or so.
I know I am leaving a lot out so please feel free to ask questions and I will answer the best I can.
Sorry for the bad picture, it was taken with my phone. I will get more pictures to anyone that is really interested.
$2800 is what I would like to get for her.
And just to throw it out there, I have a 03 400EX with all the normal bolt on's for sale too.
http://i708.photobucket.com/albums/ww85/rigger4343/250R/250r.jpg
First of all, I am located in Charleston SC. If you were to want it shipped, as long as I get good funds and you cover all shipping charges, I will build a crate and ship it from my work.
Fully gusseted 1986 frame, also modified to run the 89’ swing arm/suspension set up on the rear. 89 swing arm and 89 linkage. Works front triple rate shocks and Works rear built and valved for recreational ride for someone around 160-200 pounds. RPM adjustable width axle. Lone Star Racing plus 2, plus 1 front end. (she sits at about 50” wide). All new ball joints, heim joints and cone spacers. New 6ply tires, 400EX front brake set up with SS lines. Full chassis skid plates, FMF pipe, 36mm Duncan Racing Carb w/twist throttle. New bars and grips. New air filter and brake pads. New chain and sprockets. Good seat and plastics with a big gas tank. All new gaskets and seals. Ported motor. Milled head for higher compression (195psi) need to run race gas in her. She uses the newer style long rod crank and piston from the 88-89 motors. Crank is fairly new and I just put new crank bearings in it while I had the motor apart.
I might have 2 hours of ride time on her, if that.
I built her from just a frame over about a year and half and she has pretty much not been ridden over the last year or so.
I know I am leaving a lot out so please feel free to ask questions and I will answer the best I can.
Sorry for the bad picture, it was taken with my phone. I will get more pictures to anyone that is really interested.
$2800 is what I would like to get for her.
And just to throw it out there, I have a 03 400EX with all the normal bolt on's for sale too.
http://i708.photobucket.com/albums/ww85/rigger4343/250R/250r.jpg